Skip to content

Palmdale · Zoning · NC

Palmdale NC zoning: height, setbacks and lot size

In Palmdale's NC zone, buildings can be up to 35 ft (2 stories) tall, the front setback is 5 ft and the minimum lot size is 10,000 sq ft (Palmdale code, read October 2026).

Key points

  • Maximum building height: 35 ft
  • Maximum number of stories: 2 stories
  • Minimum front setback: 5 ft
  • Minimum side setback: 0 ft
  • Minimum rear setback: 10 ft
  • Minimum lot size: 10,000 sq ft
  • Maximum floor area ratio (FAR): 0.5

NC is a zoning district in Palmdale. Every value below was read from the Palmdale Municipal Code and links to its section (read October 2026). State laws such as the ADU and SB 9 rules can allow more on a residential lot. General information, not legal advice — read the code text and check with the city before you build.

Development standards in NC

The general rule for a typical lot in this zone. Zoning tables often attach notes, such as rules for corner lots, lots next to a residential zone, or new subdivisions only. Open “code text” under a value to see the table cell or sentence it was read from.

Maximum building height
35 ft
§ 17.48.010 · code text
Table row “Maximum Height (ft)/Stories – Primary Structure”, column “NC”: 35/2 stories
Maximum number of stories
2 stories
§ 17.48.010 · code text
Table row “Maximum Height (ft)/Stories – Primary Structure”, column “NC”: 35/2 stories
Minimum front setback
5 ft
§ 17.48.010 · code text
Table row “Front”, column “NC”: 5
Minimum side setback
0 ft
§ 17.48.010 · code text
Table row “Interior Side”, column “NC”: 0; 10 abutting a residential zone
Minimum rear setback
10 ft
§ 17.48.010 · code text
Table row “Rear”, column “NC”: 10; 20 abutting a residential zone
Minimum lot size
10,000 sq ft
§ 17.48.010 · code text
Table row “Minimum Lot Size (sf)”, column “NC”: 10,000
Maximum floor area ratio (FAR)
0.5
§ 17.48.010 · code text
Table row “Maximum Floor Area Ratio”, column “NC”: 0.5

Uses in NC

Uses the code's use tables allow in NC, or allow with a permit. Each links to its page with the code section.

When a different number applies

The code sets other values for particular lots, buildings or locations in NC:

  • Minimum side setback: 10 ft — Abutting a residential zone. § 17.48.010
  • Minimum rear setback: 20 ft — Abutting a residential zone. § 17.48.010

Not on this page

We did not find a general lot coverage, density limit for NC in the zoning tables we read. The code may still set one elsewhere — check the Palmdale Municipal Code.

Other Palmdale zoning districts

Who this affects

HomeownersArchitects and designersDevelopersReal estate agents

Frequently asked questions

What is the maximum building height in Palmdale's NC zone?

35 ft — Palmdale Municipal Code § 17.48.010.

What is the maximum number of stories in Palmdale's NC zone?

2 stories — Palmdale Municipal Code § 17.48.010.

What is the minimum front setback in Palmdale's NC zone?

5 ft — Palmdale Municipal Code § 17.48.010.

What is the minimum side setback in Palmdale's NC zone?

0 ft — Palmdale Municipal Code § 17.48.010.

What is the minimum rear setback in Palmdale's NC zone?

10 ft — Palmdale Municipal Code § 17.48.010.

General information, not legal advice.

Ask about a Palmdale property in NC

Ask GoCodebook what you can build at a specific address and get an answer that cites the section.

Ask your question

More on Palmdale