Campbell · Zoning · PO
Campbell PO zoning: height, setbacks and lot size
In Campbell's PO zone, buildings can be up to 35 ft tall and the front setback is 15 ft (Campbell code, read October 2026).
Key points
- Maximum building height: 35 ft
- Minimum front setback: 15 ft
- Minimum side setback: 5 ft or one-half the height of the adjacent building wall, whichever is greater
- Minimum rear setback: 5 ft or one-half the height of the adjacent building wall, whichever is greater
- Maximum floor area ratio (FAR): 1.0
PO is a zoning district in Campbell. Every value below was read from the Campbell Municipal Code and links to its section (read October 2026). State laws such as the ADU and SB 9 rules can allow more on a residential lot. General information, not legal advice — read the code text and check with the city before you build.
Development standards in PO
The general rule for a typical lot in this zone. Zoning tables often attach notes, such as rules for corner lots, lots next to a residential zone, or new subdivisions only. Open “code text” under a value to see the table cell or sentence it was read from.
| Maximum building height | 35 ft § 21.10.050 · code textTable row “Maximum height limit”, column “PO”: 35 ft. |
|---|---|
| Minimum front setback | 15 ft § 21.10.050 · code textTable row “Front”, column “PO”: 15 ft. |
| Minimum side setback | 5 ft or one-half the height of the adjacent building wall, whichever is greater § 21.10.050 · code textTable row “Side (each)”, column “PO”: A minimum of five feet or one-half the height of the building wall adjacent to the side property line (whichever is greater). |
| Minimum rear setback | 5 ft or one-half the height of the adjacent building wall, whichever is greater § 21.10.050 · code textTable row “Rear”, column “PO”: A minimum of five feet or one-half the height of the building wall adjacent to the rear property line (whichever is greater). |
| Maximum floor area ratio (FAR) | 1.0 See note 1 below the table in the code. § 21.10.050 · code textTable row “Maximum floor area ratio”, column “PO”: 1.0 (1) Note 1: Properties located within the Pruneyard/Creekside District 3.0 acres and larger shall be allowed to develop at a maximum F.A.R. of 2.0 as provided for by LU-8.7 of the General Plan. Properties located within the Winchester Boulevard Master Plan (WBMP) shall have a maximum F.A.R. of 1.5 as provided for on page 24 of the WBMP. |
When a different number applies
The code sets other values for particular lots, buildings or locations in PO:
- Maximum floor area ratio (FAR): 2.0 — Properties located within the Pruneyard/Creekside District 3.0 acres and larger § 21.10.050
- Maximum floor area ratio (FAR): 1.5 — Properties located within the Winchester Boulevard Master Plan (WBMP) § 21.10.050
Not on this page
We did not find a general stories, lot size, lot coverage, density limit for PO in the zoning tables we read. The code may still set one elsewhere — check the Campbell Municipal Code.
Other Campbell zoning districts
Who this affects
Frequently asked questions
What is the maximum building height in Campbell's PO zone?
35 ft — Campbell Municipal Code § 21.10.050.
What is the minimum front setback in Campbell's PO zone?
15 ft — Campbell Municipal Code § 21.10.050.
What is the minimum side setback in Campbell's PO zone?
5 ft or one-half the height of the adjacent building wall, whichever is greater — Campbell Municipal Code § 21.10.050.
What is the minimum rear setback in Campbell's PO zone?
5 ft or one-half the height of the adjacent building wall, whichever is greater — Campbell Municipal Code § 21.10.050.
What is the maximum floor area ratio (far) in Campbell's PO zone?
1.0 — Campbell Municipal Code § 21.10.050.
General information, not legal advice.
Ask about a Campbell property in PO
Ask GoCodebook what you can build at a specific address and get an answer that cites the section.
Ask your question