Fresno · Zoning · RM-1
Fresno RM-1 zoning: height, setbacks and lot size
In Fresno's RM-1 zone, generally buildings can be up to 40 ft tall and the front setback is 10 to 20 ft, with the conditions listed below (Fresno code, read October 2026).
Key points
- Maximum building height: 40 ft
- Minimum front setback: 10 to 20 ft (build-to range: the building must stand 10 to 20 ft back; applies only inside the General Plan Priority Areas)
- Minimum side setback: 10 total, minimum 4 ft per side
- Minimum rear setback: 20 ft
- Maximum lot coverage: 50%
- Maximum density: 16 dwelling units per acre (the code also requires a minimum density of 12 du/ac)
RM-1 (Residential Multi-Unit District) is a zoning district in Fresno. Every value below was read from the Fresno Municipal Code and links to its section (read October 2026). State laws such as the ADU and SB 9 rules can allow more on a residential lot. General information, not legal advice — read the code text and check with the city before you build.
Development standards in RM-1
The general rule for a typical lot in this zone. Zoning tables often attach notes, such as rules for corner lots, lots next to a residential zone, or new subdivisions only. Open “code text” under a value to see the table cell or sentence it was read from.
| Maximum building height | 40 ft § 15-1003 · code textTable row “Maximum Height (ft.)”, column “RM-1”: 40 |
|---|---|
| Minimum front setback | 10 to 20 ft Applies: build-to range: the building must stand 10 to 20 ft back; applies only inside the General Plan Priority Areas § 15-1003 · code textTable row “Front (min./max.)”, column “RM-1”: 10/20(1) |
| Minimum side setback | 10 total, minimum 4 ft per side § 15-1003 · code textTable row “> Interior Side (min.)”, column “RM-1”: 10 total, min. 4/side |
| Minimum rear setback | 20 ft § 15-1003 · code textTable row “> Rear (min.)”, column “RM-1”: 20 |
| Maximum lot coverage | 50% § 15-1003 · code textTable row “Maximum Lot Coverage (% of lot)”, column “RM-1”: 50 |
| Maximum density | 16 dwelling units per acre Applies: the code also requires a minimum density of 12 du/ac § 15-1003 · code textTable row “Maximum Density (du/ac) (min./max.)”, column “RM-1”: 12/16 |
Uses in RM-1
Uses the code's use tables allow in RM-1, or allow with a permit. Each links to its page with the code section.
- Single-family home — Allowed — see note
- Duplex — Allowed
- Apartment building — Allowed
- Senior or assisted living — Needs a conditional use permit
- Residential care home (7 or more) — Needs a conditional use permit
- Child care center — Needs a conditional use permit
- Church or place of worship — Allowed
- Private school — Allowed
When a different number applies
Not on this page
We did not find a general stories, lot size, FAR limit for RM-1 in the zoning tables we read. The code may still set one elsewhere — check the Fresno Municipal Code.
Other Fresno zoning districts
Who this affects
Frequently asked questions
What is the maximum building height in Fresno's RM-1 zone?
40 ft — Fresno Municipal Code § 15-1003.
What is the minimum front setback in Fresno's RM-1 zone?
10 to 20 ft (build-to range: the building must stand 10 to 20 ft back; applies only inside the General Plan Priority Areas) — Fresno Municipal Code § 15-1003.
What is the minimum side setback in Fresno's RM-1 zone?
10 total, minimum 4 ft per side — Fresno Municipal Code § 15-1003.
What is the minimum rear setback in Fresno's RM-1 zone?
20 ft — Fresno Municipal Code § 15-1003.
What is the maximum lot coverage in Fresno's RM-1 zone?
50% — Fresno Municipal Code § 15-1003.
General information, not legal advice.
Ask about a Fresno property in RM-1
Ask GoCodebook what you can build at a specific address and get an answer that cites the section.
Ask your question