Jurupa Valley · Zoning · I-P
Jurupa Valley I-P zoning: height, setbacks and lot size
In Jurupa Valley's I-P zone, generally buildings can be up to 35 ft tall, the front setback is 25 ft and the minimum lot size is 20,000 sq ft, with the conditions listed below (Jurupa Valley code, read October 2026).
Key points
- Maximum building height: 35 ft (At the yard setback line; parts above 35 ft step back 2 ft for each 1 ft above, up to 50 ft overall.)
- Minimum front setback: 25 ft (on any street)
- Minimum side setback: 10 ft (for the two side lot areas combined)
- Minimum rear setback: 15 ft
- Minimum lot size: 20,000 sq ft
I-P (Industrial Park) is a zoning district in Jurupa Valley. Every value below was read from the Jurupa Valley Municipal Code and links to its section (read October 2026). State laws such as the ADU and SB 9 rules can allow more on a residential lot. General information, not legal advice — read the code text and check with the city before you build.
Development standards in I-P
The general rule for a typical lot in this zone. Zoning tables often attach notes, such as rules for corner lots, lots next to a residential zone, or new subdivisions only. Open “code text” under a value to see the table cell or sentence it was read from.
| Maximum building height | 35 ft Applies: At the yard setback line; parts above 35 ft step back 2 ft for each 1 ft above, up to 50 ft overall. § 9.145.050 · code textThe maximum height of all structures, including buildings, shall be thirty-five (35) feet at the yard setback line. |
|---|---|
| Minimum front setback | 25 ft Applies: on any street § 9.145.050 · code textA minimum twenty-five (25) foot setback shall be required on any street. |
| Minimum side setback | 10 ft Applies: for the two side lot areas combined § 9.145.050 · code textThe minimum sideyard setback shall equal not less than ten (10) feet for the two (2) side lot areas combined. |
| Minimum rear setback | 15 ft § 9.145.050 · code textThe minimum rear yard setback shall be fifteen (15) feet. |
| Minimum lot size | 20,000 sq ft § 9.145.050 · code textThe minimum lot size shall be twenty thousand (20,000) square feet with a minimum average lot width of one hundred (100) feet. |
When a different number applies
The code sets other values for particular lots, buildings or locations in I-P:
- Maximum building height: 50 ft — all buildings and structures; unless a height up to 75 feet for buildings, or 105 feet for other structures is specifically permitted under Section 9.240.370 § 9.145.050
- Maximum building height: 75 ft — buildings, when specifically permitted under Section 9.240.370 § 9.145.050
- Maximum building height: 105 ft — other structures, when specifically permitted under Section 9.240.370 § 9.145.050
- Minimum front setback: 50 ft — on any boundary where the industrial property abuts a residential or commercially zoned property § 9.145.050
Not on this page
We did not find a general stories, lot coverage, FAR, density limit for I-P in the zoning tables we read. The code may still set one elsewhere — check the Jurupa Valley Municipal Code.
Other Jurupa Valley zoning districts
Who this affects
Frequently asked questions
What is the maximum building height in Jurupa Valley's I-P zone?
35 ft (at the yard setback line; parts above 35 ft step back 2 ft for each 1 ft above, up to 50 ft overall) — Jurupa Valley Municipal Code § 9.145.050.
What is the minimum front setback in Jurupa Valley's I-P zone?
25 ft (on any street) — Jurupa Valley Municipal Code § 9.145.050.
What is the minimum side setback in Jurupa Valley's I-P zone?
10 ft (for the two side lot areas combined) — Jurupa Valley Municipal Code § 9.145.050.
What is the minimum rear setback in Jurupa Valley's I-P zone?
15 ft — Jurupa Valley Municipal Code § 9.145.050.
What is the minimum lot size in Jurupa Valley's I-P zone?
20,000 sq ft — Jurupa Valley Municipal Code § 9.145.050.
General information, not legal advice.
Ask about a Jurupa Valley property in I-P
Ask GoCodebook what you can build at a specific address and get an answer that cites the section.
Ask your question